Opening the lab

Electromagnetic Induction  / CSEC Physics
move it or nothing happens
All labs
A bar magnet on a track passing through a coil, wired to a galvanometer and a lamp, above a graph of induced voltage against time.
Induced current
Lenz: the coil pushes back
N pole
S pole

Set up the experiment

Turns on the coil, N100
Magnet strength1.0×
Swipe speed1.0 m/s
Which pole goes in first
Connect the lamp
Brightness compares the power
Show the magnet’s field
The field lines it carries with it
Show Lenz’s law
The pole the coil turns into
Hide the answer
Draw your own arrows first, then reveal
Try this first: hold the magnet still inside the coil. Nothing happens, whatever the settings. Induction needs change, not just a magnet.

Then shake it in and out. The lamp stays lit, because the flux is changing the whole time. That is exactly what a generator does, only it spins instead of shaking.

If the lamp looks dim, that is the real answer: a hand shaken magnet makes very little power. Turn the turns, strength and speed right up, which is why real generators use thousands of turns and spin fast.
Voltage now
0mV
Current now
0mA
Peak this run
0mV
Peak power
0mW

How to work out the direction

Recorded runs

Swipe the magnet through, then record the run to compare setups.

Working

Faraday’s law

Whenever the magnetic flux through a coil changes, a voltage is induced across it. The faster the flux changes, the larger the voltage.

induced e.m.f. ∝ N × rate of change of flux

The N is there because each turn of wire has the same voltage induced in it, and they add up in series.

The word that matters is change. A magnet sitting inside a coil induces nothing at all, no matter how strong it is or how many turns there are.

What makes the voltage bigger

Do thisVoltage
Move the magnet fasterIncreases
Use more turnsIncreases
Use a stronger magnetIncreases
Hold it stillZero

All three of the first ones raise the rate of change of flux linkage, which is the single thing Faraday's law actually depends on.

Lenz’s law

The induced current always flows in the direction that opposes the change causing it.

  • Push an N pole in, and the near face of the coil becomes N, pushing back against you.
  • Pull that same N pole out, and the face becomes S, trying to hold on to it.

So you are always working against the coil. That is not a nuisance, it is the conservation of energy: the work you do against the opposition becomes the electrical energy in the circuit.

If it were the other way round the coil would pull the magnet in, speed it up, and generate energy from nothing. Lenz's law is what forbids that.

Why the needle kicks twice

Push the magnet all the way through and the meter swings one way, back through zero, then the other way.

  • Going in, the flux is increasing.
  • Coming out, the flux is decreasing.

Opposite changes, so opposite currents. And since the flux ends up exactly where it started, the two kicks cancel out overall.

The surprise at the centre

With the magnet exactly at the middle of the coil, the flux is at its greatest. But the induced voltage is zero.

That is because Faraday's law depends on the rate of change of flux, not the amount of it. At the peak, the flux is momentarily not changing at all, so nothing is induced even though the magnet is moving quickly.

Watch the graph as you swipe through: the two humps are either side of the centre, and the trace crosses zero exactly as the magnet passes the middle.

Power and the lamp

P = V² / R

Because the power depends on the voltage squared, doubling the voltage gives four times the power. That is why the lamp brightness changes so dramatically when you speed up the swipe.

Note on the lamp: a single swipe only makes it flash, because the voltage exists only while the magnet is moving. To keep a lamp lit you need something turning continuously, which is exactly what a generator is.

The generator

A generator does the same job as your hand, but continuously. Instead of pushing a magnet in and out, it spins a coil in a field, or a magnet inside a coil.

The flux through the coil then rises and falls smoothly, over and over, giving a voltage that alternates in the same smooth way. That is where alternating current comes from.

The same three factors still apply: spin it faster, add more turns, or use stronger magnets, and the output rises.

Where it is used

  • Power stations, where turbines spin generators to supply the grid.
  • Bicycle dynamos, turning your pedalling into light.
  • Transformers, where a changing current in one coil induces a voltage in another.
  • Microphones and electric guitar pickups, where a vibrating part changes the flux through a coil.
  • Induction hobs and wireless charging, using a rapidly changing field to induce currents.