Opening the lab

Converging & Diverging Lenses  / CSEC Physics
1/f = 1/u + 1/v
All labs
A ray diagram showing an object, a lens, its focal points, and the image formed.
Ray 1: parallel, then through F (diverging lens: as if from F)
Ray 2: straight through the centre
Dashed: virtual, where rays only appear to come from

Set up the lens

Object distance, u 30.0 cm
Focal length, f 10.0 cm
Object height, hₒ 8.0 cm
Jump to a standard case
Try this: drag the object slowly from far away toward the lens. Watch what happens as it crosses 2F, then F. The image flips from diminished to magnified, then becomes virtual and springs upright.
Object dist. u
30.0cm
Image dist. v
15.0cm
Image ht. hᵢ
4.0cm
Magnification
0.50×

Working

The lens formula

1/f = 1/u + 1/v

Where f is the focal length, u is the object distance and v is the image distance, all measured from the optical centre of the lens.

Rearranged for the image distance, which is what you usually need:

v = uf / (u − f)

Sign convention: real is positive

QuantityPositive when
flens is converging
fnegative when diverging
uobject is real (always here)
vimage is real, on the far side
vnegative when the image is virtual
Common CSEC error: forgetting to make f negative for a diverging lens. Every diverging answer comes out wrong if you skip that one minus sign.

Magnification

M = hᵢ / hₒ = v / u

Magnification has no units, it is a ratio. M > 1 means the image is larger than the object, M < 1 means it is smaller, and M = 1 means they are the same size.

For a single thin lens with a real object, the rule is simple: a real image is always inverted, and a virtual image is always upright.

The construction rays

  • Ray 1. Travels parallel to the principal axis, then refracts through the focal point on the far side.
  • Ray 2. Passes straight through the optical centre without bending.
  • Ray 3. Passes through the near focal point, then emerges parallel to the axis.

You only need two rays to locate the image, which is why the diagram here draws rays 1 and 2. Ray 3 is a check: draw it in your exam answer and if all three do not meet at the same point, something is wrong with your construction.

Converging lens: the five cases

Object atImage
Beyond 2FReal, inverted, diminished, between F and 2F
At 2FReal, inverted, same size, at 2F
Between F and 2FReal, inverted, magnified, beyond 2F
At FNo image, rays emerge parallel (image at infinity)
Inside FVirtual, upright, magnified, same side as object

These five are worth learning by heart. They come up in almost every past paper.

Diverging lens: only one case

A diverging lens is far simpler. Wherever you put the object, the image is always virtual, upright and diminished, and always forms on the same side as the object, between the lens and the focal point.

That is why diverging lenses are used in peepholes and wide-angle viewers: they shrink a wide scene into a small upright picture.

Where lenses show up

  • The eye. A converging lens forming a real, inverted, diminished image on the retina.
  • Magnifying glass. A converging lens with the object inside F, giving a virtual, upright, magnified image.
  • Camera. Converging lens, object beyond 2F, real image on the sensor.
  • Projector. Converging lens, object between F and 2F, giving a real magnified image on the screen.
  • Short sight correction. Diverging lenses, to move the image back onto the retina.

Exam technique

  • Draw a clean scale first. Mark F and 2F on both sides before drawing a single ray.
  • Use a ruler. Freehand ray diagrams lose marks even when the physics is right.
  • Arrows on rays. Show the direction light travels.
  • Dashed for virtual. Backward extensions and virtual images must be dashed, never solid.
  • Describe fully. Real or virtual, upright or inverted, magnified or diminished, and where. Four parts, four marks.